Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
This great article following next in relation to Tools You Need to Install a New Bathtub is relatively captivating. Read on and make your own personal conclusions.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard task. If the old bathtub is readily available, the job can move easily; if you need to open a wall to get rid of the old bathtub and also position the new tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually qualified on your own for the task and are comfortable trying it. As opposed to hiring a contractor to take over a halfway-completed task, it is much better to take into consideration employing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This write-up will aid you install a new tub in your bathroom if you have actually already purchased a new bathtub and don't require to change the setup of your previous supply of water pipes.
Your devices and also product checklist ought to comprise the following:
Planning for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed position. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level reviews level.
To install taps, fit all-time low of the furthest versatile tap connector to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and check all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the tub and likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub needs to wait up until the bathtub has actually been utilized at least once as this will certainly settle it into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the faucet and the sink. Secure the faucet in place with the manufacturer offered backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the activity experienced when the tub remains in usage. The sealant can split fairly early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader about Tools You Need to Install a New Bathtub , I thought sharing that portion was worth the trouble. Sharing is caring. Helping others is fun. Thanks for your time. Please come visit our blog back soon.
This Resource Report this page